sonic daddy
New member
We changed the tranny fluid and the engine oil today now we have leak from the plastic oil filter cap new oring new oil filter any idea what could be wrong?
oil filter housing leak
- Thread starter sonic daddy
- Start date
sonic daddy
New member
O ring looked good cap went on straight possible its cracked not sure I will replace with new cap tomorrow don't Know what else to do.
sonic daddy
New member
Figured out what was leaking the nut on top of housing leaks where it's mounted to housing.
Smartdave
Member
OIL contamination in coolant reservoir cause and fix
Ok oil cooler changed
It's pretty simple. It's right behind the exhaust manifold.
Steps:
First remove heat shield. (Pita).
The loosen all exhaust manifold nuts (10mm)
Unplug O2 sensor
Remove 3 1/2 nuts holding exhaust pipe to cat. (Cat is part of exhaust manifold)
Remove two 3/8 head bolts holding cat to engine, underneath by flange.
Remove dipstick tube, it's an o ring that holds it in. Drain oil first before removing dip stick
Remove exhaust manifold. I also removed both engine hoist points (12mm head)
Once manifold is removed you can see the oil cooler. Remove 4 t-30 screws from the tubes, one at waterpump and one at thermostat housing.
Remove 5 3/8 bolts from cooler and slide off last tube leaving it in place.
You do not need to buy new tubes but... get all new seals from the dealer. Like $10 in total
Make sure rubber seals come off with cooler
Then clean everything
Then replace cooler
Re attach tube to water pump and thermostat housing
Install manifold.
Bolt up flange.
Re attach o2
Add coolant and oil
While everything was apart I cleaned all threads with a tap and die
Everything was put back together with anti seize
All in all I had zero frozen nuts or bolts and took about 2.5 hours to change everything over
Hope this helps
Sent from my iPhone using Tapatalk Pro
https://r.tapatalk.com/shareLink?ur...share_fid=38994&share_type=t&share_pid=369595
Sent from my iPhone using Tapatalk Pro
Ok oil cooler changed
It's pretty simple. It's right behind the exhaust manifold.
Steps:
First remove heat shield. (Pita).
The loosen all exhaust manifold nuts (10mm)
Unplug O2 sensor
Remove 3 1/2 nuts holding exhaust pipe to cat. (Cat is part of exhaust manifold)
Remove two 3/8 head bolts holding cat to engine, underneath by flange.
Remove dipstick tube, it's an o ring that holds it in. Drain oil first before removing dip stick
Remove exhaust manifold. I also removed both engine hoist points (12mm head)
Once manifold is removed you can see the oil cooler. Remove 4 t-30 screws from the tubes, one at waterpump and one at thermostat housing.
Remove 5 3/8 bolts from cooler and slide off last tube leaving it in place.
You do not need to buy new tubes but... get all new seals from the dealer. Like $10 in total
Make sure rubber seals come off with cooler
Then clean everything
Then replace cooler
Re attach tube to water pump and thermostat housing
Install manifold.
Bolt up flange.
Re attach o2
Add coolant and oil
While everything was apart I cleaned all threads with a tap and die
Everything was put back together with anti seize
All in all I had zero frozen nuts or bolts and took about 2.5 hours to change everything over
Hope this helps
Sent from my iPhone using Tapatalk Pro
https://r.tapatalk.com/shareLink?ur...share_fid=38994&share_type=t&share_pid=369595
Sent from my iPhone using Tapatalk Pro
LizzyTheLez
New member
One day while driving I could smell the oil burning when i was stopped at a red light then i noticed that there was a little bit of smoke coming from under my hood, so i pulled over and looked at everything thinking that when I had an oil change before maybe they did not put the oil filter cap back on the correct way. took the oil filter cap off cleaned it up took the O ring off cleaned it off and put it back on wiped off as much oil as i could and kept going. car was doing good and then all of a sudden im at a light again the smell comes back and smoking under the hood. yet again i pull off to check the problem only to find the oil is only leaking from below what the oil filter sits. take it to the shop they put my car on the rack and can see the oil that is caked on so they clean it up fill the oil and tell me to come back in a few hours. go back for them to see the fresh oil that has leaked check the oil cooler housing and it is not cracked.
normally I do all my work my self but this time I'm having a shop do it for me. mechanic told me that it would be okay to just change all my gaskets that my housing is not cracked. going to spend $150 on labor (discounted due to wife working with oreillys) and $80 on gaskets all but the exhaust manifold was bought through dealership thats also with a discount.
crossing my fingers for this to be the fix!
original gasket price from dealer was $116 exhaust manifold gasket was $10
thank god for having a wife working at Oreillys
normally I do all my work my self but this time I'm having a shop do it for me. mechanic told me that it would be okay to just change all my gaskets that my housing is not cracked. going to spend $150 on labor (discounted due to wife working with oreillys) and $80 on gaskets all but the exhaust manifold was bought through dealership thats also with a discount.
crossing my fingers for this to be the fix!
original gasket price from dealer was $116 exhaust manifold gasket was $10
thank god for having a wife working at Oreillys
