LAUNCHED- Forge 1.4T BPV and ATMOSPHERIC BOV **DIRECT FIT**

BNRacing

BNRacing

Supporting Vendor
As you all know, these have been under development for quite a while. Well, we're finally ready to start selling them. Pricing is set at $165 with FREE SHIPPING


Get em here!

BPV- Forge Motorsports 1.4T Recirculating Bypass Valve

BOV- Forge Motorsports 1.4T Atmospheric Bypass Valve

NOTE: The ATMOSPHERIC BOV will REQUIRE a Trifecta ECP enabled tune. Most Sonic 1.4T tunes (and ALL 1.4T Cruze/Sonic budget tunes) are ECP enabled. If you are not sure if yours is or not, please contact us. If you do not have an ECP enabled tune, we will update the tune for this mod at no additional cost.


Sound clip of the BOV is on the product page :cool:
 
rdss

rdss

Junior Member
No problem Jerry, glad I could help! I will post a lessons learned in here on the install soon.
 
BNRacing

BNRacing

Supporting Vendor
installed-

forge.jpeg
 
rdss

rdss

Junior Member
Yeah, it doesn't have that quack.... I mean Chirp sound which I like. I'm going to take it out here in a bit after I cool off and get cleaned up and get a driving video. I go on det this weekend for a couple of weeks so I will get back and run it for a few weeks and then give a better review.

There where some lessons learned on this guy. This isn't a quick and easy job, its mot hard, just takes time and you're going to be cut and bruised when you're done. Just take your time, Jerry said there was no torque specs so I went snug plus a small bump and will check them again Saturday. Eric probably will agree that the area you're working in is extremely tight! Using the standard 3/8 socket set and a T30 bit made things hard. I had to pull the DDM heat sheild and intake to make some room to move around. I went in from the air box end by the AC lines and had to reach all the ways across with a long extension. Expect dropped bolts, it's going to happen and just take your time, they usually make it to th bottom or get stuck on the AC compressor. The stock valve kinda spills out, you will have a cover, spring and diaphragm. I just pulled the guts out and put it in the forge bubble wrap bag and back in the box. I also recommend getting the vacuum line installed on the nipple prior to putting th BOV/BPV into place. It's easiest to set the bolt closet to the radiator, then the top and then peek around and find the flange for the third bolt hole in the back. To get the bolts back in I tried taping to the valve (note painters tape on the valve in above pic, need to pull that before the test drove.....), that didn't work out all that well. What did was putting painters tape on the tip and pushing the bolt on for a snug fit. Also, as usual, patience is key. And a final not, it's only three bolts, no hidden bolt ninjas here!!

1351281452676.jpg
 
Last edited:
rdss

rdss

Junior Member
What are you taking about?! How can it sound like a queef when it doesn't go quack?!
 
rdss

rdss

Junior Member
I like it, it has more of a hard initial push with a drawn out psssshhh when venting. You really can't tell much difference with the windows up but with them down you can definitely tell its fast and furious.....lol but not over bearing. I'm enjoying it so far and will get some more miles on it tomorrow and let y'all know what I think of it.
 
Preloader

Preloader

The M32 Martyr
- 3 questions

If your tune is ECP enabled, can you install the BOV with no other action required? The ECU will "know" to operate on speed density once the BOV is installed? And lastly, will my e85 SEG (sh¡t-eating grin) tune be ECP enabled?
 
Eric Smit

Eric Smit

Enforcer
1) Yes. ECP is speed density basically. it will always be. BOV will be bolt on.

2) See 1.

3) if its not, it can be, for the low price of nothing.


-Eric Smit
 
rdss

rdss

Junior Member
If you're tuned to ECP you're running on MAP already so you're good to go no matter what valve you use so swap away. I went from the factory valve to the BNR BOV and just hopped in the car and went for a drive.
 
Preloader

Preloader

The M32 Martyr
For the sake of knowledge what does ECP directly stand for?

Plz don't say speed density.................. Eric :blankface:
 
You must log in or register to reply here.

Latest posts

Members online

Total: 200 (members: 2, guests: 198)

Share this page

Top